Titanium dioxide for water-based paint

This product is recommended for latex coatings with low weather resistance requirements. It can also be used in interior coatings, primers, plastic masterbatches, plastic pipes, rubber, leather facing paper and other industries.

падзяліцца

ЗВЯЖЫЦЕСЯ ЗАРАЗ загрузіць у pdf

Дэталі

Тэгі

ДЫСПЛЕЙ ПРАДУКЦЫІ

Кіраванне цэласнасцю, дастатковы запас, ідэальнае пасляпродажнае абслугоўванне, высокая якасць прадукцыі, разумныя цэны і ўважлівае абслугоўванне.

PRODUCT DISPLAY

спецыфікацыя

Product features:
This product is anatase titanium dioxide without surface treatment, which is ultra-finely ground. It has fine and uniform particle size, narrow particle size distribution, high purity, good whiteness, high tinting power and hiding power, and excellent optical properties, pigment properties and dispersion properties.

Спецыфічныя для галіны атрыбуты

нумар CAS

13463-67-7

Іншыя атрыбуты

Item	Technical indicators
Tinting Power	≥1300
Oil Obsorption	≤24 g/100g
Water Solubility	≤0.5%
PH	6.5-8.5
Удзельнае супраціўленне	≥2000 Ω.cm
Рэшткі сіта (325 меш)	≤0.06%
Dispersibility (Hager mann coefficient)	≥4.5
Whiteness	≥96.0%
Brightness	≥96.50%
Rutile content	≥98.0%

Час выканання

Колькасць (кілаграмы)	1 - 25	26-1000	1001 -25000	>25000
Час выканання (дзён)	5	7	15	Дамаўляцца

How to use titanium dioxide for water-based paint?
The method of using titanium dioxide for water-based paint mainly includes the following steps:

‌Preparation phase‌: First, prepare the required materials and equipment. Make sure the furnace or melting furnace is clean and tidy to prevent impurities from mixing in. At the same time, prepare a sufficient amount of water-based titanium dioxide.
‌Heating equipment‌: Heat the furnace or melting furnace to the melting point of water-based titanium dioxide, usually 1830 degrees Celsius. Note that too high a temperature may cause water-based titanium dioxide to oxidize or burn, so the heating temperature must be carefully controlled.
‌Adding water-based titanium dioxide‌: Gradually add the prepared water-based titanium dioxide to the heating equipment and stir evenly to ensure that it is completely melted. A stirrer or stirring rod can be used to speed up the melting process.
‌Check the finished product‌: Once the water-based titanium dioxide is completely melted, pour it into a container to cool. After it cools and solidifies, the smelted water-based titanium dioxide can be obtained.

‌The role of titanium dioxide for water-based paint‌:
‌Improve the quality and performance of the paint‌: Water-based titanium dioxide can stabilize the suspension state and prevent precipitation, thereby ensuring the quality and performance of the paint‌.
‌Enhance the hiding power and glossiness of the paint‌: Water-based titanium dioxide has excellent whiteness and hiding power, which can improve the hiding effect and glossiness of the paint‌.
‌Improve the physical and chemical properties of the paint‌: Adding water-based titanium dioxide to plastics can improve the heat resistance, light resistance, and weather resistance of plastic products, and improve their physical and chemical properties‌.
‌Precautions for use‌:

‌Appropriate use‌: The amount of anti-settling agent added should be carried out according to the specified ratio. Excessive use will affect the quality and performance of the paint‌.
‌Storage conditions‌: Avoid direct sunlight and high temperature environment during storage to prevent the anti-settling agent from failing‌.